Get 1GB FREE samples, music production courses + templateshttps://warpacademy.com/free-stuff-bundle
Try Warp Academy for FREEhttps://warpacademy.com/free 
Summary of Auditory Memory in Humans: https://www.sciencedaily.com/releases/2014/02/140226174439.htm 
Study of Auditory Memory in Humans: https://journals.plos.org/plosone/article?id=10.1371/journal.pone.0089914

Burning in is the concept that a new loudspeaker, fresh from the factory, needs a period of running it before performance is optimal and that the sound of a speaker changes over time. By running the speaker over a period of time, some people say that you’re going to get it into a stabilized or optimal state.

I’m always reviewing and testing studio monitors so this is quite relevant for me and I wanted to dig a little deeper into this. Right now I’m testing the Neumann KH420 and the Focal Trio 11 Be monitors. It’s quite interesting because different people recommend totally different things. We’re going to peel back the onion, dig back into where this came from, what’s involved, and figure out if it’s relevant for you.

Let us think about what parts can change their properties permanently in an active loudspeaker:

Electronics – There is insignificant change with use over time. Permanent changes are usually the result of poor parts selection in design, early parts failure (bathtub curve), or user abuse. Some temporary change over short periods is seen due to heating up of components, but this resets when the electronics cools down. Active loudspeakers do not suffer significantly from these temporary changes as the sensitive crossover parts are positioned before the amplifier and so do not heat up much.

Cabinet Mechanics – If this changes it is not well built!

Drivers – The moving mass cannot change otherwise it means that something has fallen off, or
some extra mass has been added. The self-damping should not change significantly otherwise it would mean that the cone material is falling apart. These two situations would only happen in the case of loudspeaker abuse or accidental damage. The suspension and surround can change their stiffness over time; however a good design should be robust to these minor changes. Even quite large, and highly unlikely in a correctly working loudspeaker, changes (doubling or halving the stiffness) will alter the overall loudspeaker performance by less than 1 dB in the low-frequency region only. Temporary changes are seen due to the voice coil heating up (thermal compression), but this resets when it cools down.

Psychoacoustics – A human’s auditory memory is VERY short, less than five seconds. This fact is well-known in the academic community, so one sees controlled ABX type listening tests with fast switchers to avoid the listeners forgetting what they just heard. Typically when burning-in loudspeakers a user listens to the loudspeaker for a while, does the burn-in over a long time period (say 24 hours, or even up to a week), then listens again. Having done this they are naturally inclined to hear a difference.

This is what Focal recommends:

Focal recommends a running in period of 20 hours. They say the speaker’s mount is stiff from the factor and that it needs to be worked in. They say this is required to adapt the speaker to the temperature and humidity conditions of its new environment. However, they don’t say why they believe this or support it with data of any sort. So it weakens their argument in my opinion because they don’t appear to have done any testing to validate their claims.

Focal’s recommendations for burning in: https://www.focal.com/en/focal-teach/what-is-the-running-in-period 

This is what Neumann concludes:

Our decades of experience in servicing products has shown that products which have been in normal use for many years typically have less than 0.5 dB of variance compared to specification. The largest source of variance is seen when drivers have been replaced, therefore recalibration to production standards is advised after servicing. If the long-term specification is stable, the short-term specification should also be stable.

Concluding, burning-in loudspeakers came from the past when poorly-designed passive systems were common. Today we have well-designed active solutions that can be used straight out of the box. To take an analogy from the automotive industry: cars used to require a running-in period of 500 miles (800 km), these days it is not required.

Neumann’s recommendations for burning in: https://en-de.neumann.com/product_files/7942/download

If you want to burn your speakers in anyways, here’s how you do it:

• Start by playing low volume music with minimal bass
• Gradually increase the volume, and switch genres over a 20-60 hour period


I hope you found this useful and informative! Catch you on the next one. Cheers!

★ STAY IN TOUCH ★

Discord: https://discord.gg/QSYvFSM
Instagram: https://instagram.com/warpacademy
Facebook: https://facebook.com/warpacademy

★ ABOUT WARP ACADEMY ★

If you’re new to Warp Academy, we empower artists to reach their full potential, create exceptional music, and live their passion. We’re a global, online collective that includes producers, audio engineers, label owners, sound designers, agents, coaches and more. We hook you up with all the education, software, and sounds you need to create professional quality music and launch a successful career. Join us!

Try Warp Academy for Free https://warpacademy.com/free-stuff-bundle
Join our Discord Server: https://discord.gg/QSYvFSM

Like what you see? sharing is caring!